Hi,
I would like to flash my new vrbrain 5.2 using JTAG.
At first, I can't find any documentation about this or any datasheets of this board.
Then, when I plug the four connections on the st-link, the software says me "internal command error" when I
Read more…works just fine on ubrain.
connected to the telem port using 2mm pitch header it works just with an APM.
For those wonderiung what it is it converts some of the mavlink data to Frsky Taranis format to see it it directly on your taranis transmitter.
Read more…Hi,
When using a VRMicroBrain with a APM:Plane, should the buzzer make any noise? I have a buzzer from a PixHawk( like this http://www.digikey.com.au/product-detail/en/CPE-827/102-1620-ND/1738894) .
I attached one wire to the "buzzer" pin and the ot
Read more…Hello!
I recently bought from a german hobby colleague a VR uBrain board.
I own already several Pixhawks and use them with different kinds of uBlox GPS modules.
Since I found the NEO-8M GPS a quite good option I also would like to use it with my new
Read more…To all VRBRAIN users, we have just published version 3.2 of the APM:Copter firmware.
You can install the firmware using Mission Planner "Initial setup-->install firmware and selecting the 3.1.5 version in the main window.
Unitl the official 3.2 rele
Read more…Hi all,
Which is the +5v, gnd, tx and rx pins of the 5 pin connector for GPS and 4 pins connector for the magnetometer on the microbrain?
Read more…Hi,
I have a problem with connecting the microbrain to MP using the original microtelemetry module on the microbrain, and this module on PC win8. I go in initial setup > optional hardware > 3DR radio. I select COM7 (silicon labs.....USB to UART....)
Read more…First post and a quesion. Sorry :)
I am installing a VR Brain 5.1 to control a large quad. I have the VR Brain and GPS units connected up on the bench and everything seems to be working except the GPS and external compass. I have flashed the board u
Read more…Hi, I need to know which basic settings must be done at first to have a successful first flight.
I did all the calibrations (acc, mag, radio), set the type of vehicle etc. in the initial setup. Than I disabled the preflight check, calibrated the ESCs
Read more…Hello,
I have two VR cards:
One VR Brain 4.5 with uBlox 6 (3DR GPS) flying an Hexa and one µBrain with uBlox 8 on a smaller Quad.
I upgraded both to latest rc10 version. VR Brain 4.5 is OK (also with EKF) but µBrain GPS performance is poor. Compas
Read more…Hello,
I have 2 Led and Buzzer.
Led sequence is OK (GPS fix and Motors), but buzzer is always beep-beeping as soon as µBrain is On. When I arm the motors Beep sequence is OK but Beeping is stil there.
Is there a condition trigging Alarm?
Fence is
Read more…Just a small question: After some rotation of my quad the heading in the HUD continues to rotate for a certain time and the direction of North is very artistically moving;-) I'm powering the micro Brain from an ESC with 5V on the recommended port. Th
Read more…Hi,
As mentioned in my other thread I have converted my quad to an octaquad. I am now using a taranis on SBus, and this all looks good on the radio cal page.
firmware loaded with mission planner.
initially I thought it was wiring yesterday so I rew
Read more…Hi guys, Any plans of making ArduCopter 3.3 available as firmware upgrade from Mission Planner for VR micro brain 5.1? I would like very much to use the new functions. Probably I could compile it myself, but it would be great to have the official ve
Read more…Probably related to the Failsafe problem, but i have an issue with 2 different copters running micro Vrbrain 5.1 and D4R-II 27ms receivers(3.2 rc2) connected with ppm. Both of them go in failsafe after a while. No Rssi problems on my tarranis. In th
Hi,
am actually waiting release of mini telemetry option to buy vrmicrobrain and ublox8 solution.
It will be used on a flywing wing (FX79). I just wonder one question : is it possible to connect a pitot airspeed sensor to vrmicrobrain ?
Thanks.
Oli
Read more…
In this video is possible to see the quality of autonomous fly on VR uBrain 5.
We set the VRX300 at 15 m of altitude 10m from the car and activate the follow mode .
In parameter i set max speed of 8 m/s .
The GPS used in the test is the new VR GP
Read more…Hello Roberto,
Despite all caution today the USB port is broken.
Unfortunately I have no possibility to repair.
there is a solution for me?
greetings, Helmut
Hello,
Can someone tell if FMU AUX5 (pin 54 on Pixhawk) is available on the ubrain 5.1 to connect a lidar lite ?
Or any hint how to connect it ?
Thanks
Read more…Hello,
I have µBrain with latest firmware (3.2 rc4).
Is Spline navigation implemented (in mission planner navigation option we can choose Spline trajectory at waypoints)?
Regards,
Marc
Read more…