Hi!
I have some SAMBA55 GSM/GPRS USB Stick modules that not are used anymore.
The Samba 55 contains a Siemens MC55 GSM/GPRS board
I have ordered a breakout board, and my plan was to use it as a telemetry modem... for my previous quad
Read more…Hello. Today I finally got my 6 mode flight switch working. I'm using a Futaba FT-T8UAP radio and I was having some troble selecting the switch to tamper with. Let me say thay the 2 or 3 position switches can't be replaced with a pot. I believe the e
Read more…Beeing a bit hard to find great looking frames and resistent ones at an affordable price, I recentlly came across with a site selling some beautifull alluminium frames here in Portugal. If you like to take a look, here's the link BeeDrones
Read more…Hello. I don't know if you are aware of this page, wich I believe to very usefull when calculating power requirements for helis, planes and multicopters : eCalc
Read more…Hi everyone
I have been sitting on the fence trying to decide if I should get myself a Multipilot32 system.
I am currently using the Standard Arducopter2 boards with the 2.0.37 code. I have been very pleased with it thus far. I always want to take th
Read more…Here's a scene from Philanthropy
Awesome Battle is Awesome! (MGS: Philanthropy) from Hive Division on Vimeo.
Hello everybody!
WHO'S THIS?
I'm Giacomo and I'm the founder and coordinator of a Venice area-based filmmaking collective known as Hi
Read more…Hello
I am having trouble setting up my board. I have the board configured the following way.
The USB<->RS232TTL outputs Rx,Tx, Gnd which are the yellow, orange, green wires in the picture. I put the ground wire to JP19-1. I am feeding 5V to the
Read more…Hello
I am a new comer here and my name is Jean-Claude
I saw in the "learning center" tab that 3 webinars heve occured
|
I just got my shiny new Multipilot32 and IMU boards from Italy today. I must say I was quite disappointed with the quality of these production boards as shipped to me. Some of the issues are as outlined below:
1. There is no way that solder paste
Ciao Ragazzi,
questo e' un tema fondamentale per continuare a volare con serenita' cerco di esporre la mia autoregolamentazione , chi mi conosce sa' che sono una persona molto prudente e cerco quindi anche in quello che faccio di mantenere margini di
Hi, Roberto Navoni,
I have just joined the visualrobotix. I do all the compile according to the developer manual from parrot but it doesn't work. Now I just want to get a correct Linux Example for firmware 1.4.6 and I can learn from. My ability is
Hello,
Does anyone have an eclipse workspace that is setup for the Arducopter32 (or any of the other branches?) that they'd be willing to share?
Thanks
luke
Read more…Hello everyone!!
I would like to get one of these systems and start playing with it. I dabble in embedded systems, working mostly with ARM and AVR stuff. Lately I've been playing a lot with the mbed platform which is basically an LPC1768 ARM core
Read more…
Basic ArduPiratesNG32 PreFlight Check.
Ecco il mio modesto contributo per quelli che vogliono iniziare quest'avventura.
Non esitate a suggerirmi dei miglioramenti.
In this video you can see a short video introduction to Multipilot Board. (Italian Version winth subtitle):
The Hardware part that you need to build your multicopter are :
1 MultipilotBoard.
3 Gyro Sensor.
4 I2C ESC.
1 RC Reciver with Serial P
Read more…Dear Friends,
today with a use we had some problem on usb dfu driver .
So if you use the windows 32 you can use the driver in directory driver/dfu in vride main directroy. So you can connect the board and use the usb bootloader.
If you use a 64 bit w
Read more…Today I made some tests with my BLMC's. With a 50 Hz PWM Signal they work fine, but connected with the MP32 they don't start, so I had a look with my Osziloscope and found out that my MP32 sends it's PWM with 550 Hz. That's maybe to much for my Turni
Read more…Work In Progress ... Invite the other people to open same thread with his name and his creation description.
Buongiorno Membri del Clan,
questo e' il primo post orientato alla presentazione delle informazioni necessarie all'assemblaggio di un quad
Read more…