Unmanned Vehicle University is the first to offer a completely online accredited Masters and Doctorate Degree in unmanned systems engineering. To learn about a career in unmanned systems download our recent interview with small UAS news. The intervie
Read more…Dear All,
I have bought THREE Multipilot32F1 (http://www.virtualrobotix.com/page/multipilot32-1 ) and Two VR IMU with GPS (http://www.virtualrobotix.com/page/vr-imu-10), all of them all brand new, Since I have shifted to other platform, so I would li
Read more…Dear friends i Open this task because a lot of people ask me how set pid and how it work .
So now i work on altitude hold setup and Loiter doing some test and Jason release also some demo program for test the setup for standard loiter revision of cod
Read more…I put the following post on the ChibiOS site, and thought somewhere on VR might be of assistance as well, as it pertains to the MultiPilot32 project. The tutorial I refenced is located here: http://www.chibios.org/dokuwiki/doku.php?id=chibios:article
Read more…Just to know, I read a lot about your chibios implementation on multipilot32 past year.
How far it goes? Do you any working code?
Read more…Hi!
Is there an alternative to Diydrones 3DR telemetry radio that is compatible with MissionPlanner?
Read more…Hi!
Is it possible to connect a current sensor to the MP32F4 V3 and get current readings using mavlink ?
Something like this: http://www.ebay.com/itm/100A-AC-DC-Current-Sensor-for-MCU-AVR-PIC-etc-FPV-RC-Robots-or-other-projects-/260875065893?pt=LH_De
Read more…I am not able to get the ST Flash loader to recognize the STM32 on the MP32. I get the following error: "No response from taget, the Boot loader can not be started. Please, verify the boot mode configuration and the flash protection status ...".
Set
Read more…Dear Friends,
in the last year we doing a great job with our Multipilot32 hardware based on STM32F1.
After 1 years of development I'm very happy to present the evolution of MP32 the new MP32V3F4
So this new board is very similar to old one ,same pi
Read more…Today I had my second test flight with the latest Firmware.
The Board tested was the VRIMUFULL with the MP32V3F1 and the BMP085 barometer.
Recent changes include:
- Updated default values for Stabilization
- Changed main loop timing.
- Fixed a memo
Hi,
is there a schematic for the MP32F4?
I think it is rather important for programming as I need to know which ports are on which pins and how is the MPU6000 connected?
Can I assume it is similar to the V2? (except the MPU6000)
Martin
Read more…Hello, I have the MP32 F1 with the VRIMU navi board and I have software version 2.0.49. I was trying to upload last available version 2.22xp2 PIDT1 but no success.
1 - I downloaded the vr ide 0.0.5.4.0 and unzipped
2 . Downloaded the 2.22xp2PIDT1 fir
Read more…Can I upload a binary which is compiled for the MP32F1 to a MP32F4 and will it work?
I'm asking as I have already bricked too many things in the past ......
Martin
Read more…Just received my board today, Thanks! I just noticed that my board doesn't have the micro SD card socket installed like the board on the instruction page. Is this something to added later? Thanks
Read more…I ordered the Olimex USB-OCD-H and it will arrive tomorrow, so I am preparing myself for some challenges. My goal is to jtag / debug one of the early ChibiOS multipilot examples, something simple.
Does anyone have the OpenOCD-GDB startup/debug/fla
Read more…Roberto,
I can’t reply to the ArmCopter Dev Group Discussions, but I wanted to add to the thoughts. I think that your hardware is far more advanced than where ArduPilot is at.
I am a COMPLETE novice, so simple is good. I do want to go far beyond t
Read more…Hi
I´m planning my new quad/hexa frame to use with an MP32F4-IMU
1. Is it recommended to use vibration reduction mounts for the controller?
2. Is there a dwg file showing the mounting holes needed to mount the mp32fx controller?
Read more…Hi!
Anyone tested frsky telemetry to transfer telemetry data from the MP32 controller ?
On the frsy with telemetry there is a 2 way serial port that can be used to transfer telemetry data.
Is it possible to connect the telemetry port on the control
Read more…Hi!
I'm new to mp32 and have start planning my new quad.
Can the mp32 be used with only a Spektrum DSM2 satellite module, or do I need a complete receiver?
I lost my quad and need a new receiver to vork with my Spektrum DX7, and when ready the new MP
Read more…I´m 41 years old, from Norway. I work with IT (since 1999) it in a bank (have the responsibility for the computers, servers, network..) Before that I worked with electronics like TV, phone systems, computers..
I have created some windows applications
Read more…